How To Use a Chainsaw For Felling a Tree

Let’s assume a big pine tree is running your property and you can’t just sit behind. So, you called a tree service to come down and have a check. But after they did, it was time to quote a certain amount. I was expecting a minimal price but to my surprise, they quoted a much higher demand. My mind went numb for a moment and I quickly turned down their offer. Another thought was popping into my mind.

Why don’t I just buy a chainsaw and do the job for myself? It could not be so hard. And I was right, with some patience and know-how, I cracked the chore. Today. I’ll be discussing my story with you all on how to use a chainsaw.

How to Use a Chainsaw: 3 Key Techniques

To use a chainsaw, you need some basic idea on power tools and of course proper safety guidelines. Anybody can try some simple steps to deal with basic tree cutting or pruning using a chainsaw. Let’s start the topic without waiting any further.

Learn 3 Techniques with Chainsaw

To operate a chainsaw, one needs to master a few techniques. Before that, one needs to always stand to the powerhead’s left side. In most of the saws, the design held the cutting attachment to be on the right side. So that user can be accordingly and easily.

You can learn three tasks or techniques with the chainsaw on a tree. These are:

  1. From a downed tree, you can remove the branches and limbs. This is known as Limbing.
  2. The downed tree’s trunk is cut to a length, this is known as the bucking technique.
  3. To deal with an upright tree, a controlled and secure method is used known to be felling.

Get Some Equipment

  • Complete face protection with a helmet that comes with guard and goggles.
  • Work gloves that are good to grip and do not slip.
  • Protective chaps.
  • Logging boots.
  • Hearing protection with earbuds or earmuffs.
  • Engine oil.
  • Gas.
  • Chain oil.

Be Familiar with Your Workspace

The area where you are going to use the chainsaw needs your concern first. Be aware of that spot and figure out the escape routes. This is a place where you can run to if there is a stance of mistake or mishap. Also, you need to escape once the tree starts to fall.

In some cases, the tree can fall into an undecided direction. So being previously prepared for such sudden scenarios is the wise step. Once a nobleman called chainsaw a widow-maker for these types of situations. Chainsaws are pretty tough to work with as well as dangerous. So be sure with your working plan and never take a chance with the terrain you’ll be working on.

Have a Good Look at Your Chainsaw?

You need to have a final checkup before jumping into the process. Have a look from head to toe of your chainsaw. The chain needs to have good tension. Try tugging the chain up from the guide bar. Then see if it is possible to disengage the links from the guide or nose area. If yes, then the chain is too loose. You need to tighten the tension. Otherwise, injuries are bound to happen.

You should always follow the machine’s instruction manual for such tension or tightening jobs. A scrench is included to perform such chores. This tool is a combination of wrench and screwdriver. It comes along the machine. A good indicator that your chain is tight properly is when you try pulling it should give slightly but no disengagement from guide should take place.

Sufficient Fuel Is A Must

In the maximum gas machine, you need to check the levels before using it. Check and fill the tank before starting it up.

There are two-cycle engines that use both gas and oil. You need to mix them in the tank for functioning. For such need simply but two-stroke oil. And then you need to know the manufacturer ratio for filling the tank.

In most cases, the ratio is around 50:1. It is pretty much 2.6 ounces oil into a gas gallon. Then using the ratio simply fill the tank. You also need to fill the chain lube reservoir. Use specific chain oil for this step.

Setting the Chain Brake, Choke & Primer

Let the chainsaw lay flat on the ground with the bottom-down position. You need to punch the brake forward. This will make it lock. You can find the brake in the top handle.

Next, simply turn the choke on if it’s a gas-powered chainsaw. There could be a primer button. In that case, push it four to six times. This will pull gas and turn the machine on. In electric chainsaw, a simple safety switch turns on following power switch press will turn it on

If It’s A Gas-Powered Chainsaw

This step is only for those who are using a gas chainsaw. If it’s an electric one, move on to the next step. Let your right foot place on the back handle. Now use your weight pressure to secure the saw.

Using your left hand simply holt the front handle firmly. Go for the starter rope and pull it with your right hand. Bring it to full length. After four to five pulls the engine will start. You should adjust the choke again if the engine does not start.

After Engine Start-Up

After the engine is on, the chain needs to run. You need to use a switch or trigger for chain movement. Let your foot secure the saw and use hands for a firm grip. Then use a side or angled position for cutting with a saw. This is the best way to avoid injuries during kickback.

Once you are ready to cut, let the chain brake release. This will bring the full-throttle mode. Without applying too much pressure simply utilize the momentum of blade and chain. You need to gradually draw into the wood.

Once the cut is over, simply release the throttle. Make sure you do so after the blade has stopped moving completely. Turn off the saw and let it cool for storing.

How To Safely Use a Chainsaw

Final Words

See? Using a chainsaw is pretty simple and straightforward. However, don’t expect to be completely mistake-free with your first time. Even if you have learned how to use a chainsaw, there are more to come into your knowledge. And that’s only possible with constant practice and trying. So have patience and keep trying this chore yourself. One day you don’t have to bother hearing the high tree service charges anymore.

Leave a Comment

shares